combined ceiling

Combined tension ceilings and drywall

Making modern interior designer in relation to developed mainly with tension-type ceilings. However, much more winning recognize such variations as combined ceilings. This is the original design and pleasant appearance - thanks to its flawless surface, and at operation, they will not change their shape and do not lose their good qualities.

The ability to create interesting design options and attractive volumetric composition was the reason for the association of suspended ceilings combined in a very special group. This does not diminish the popularity of suspended ceilings made of PVC, but solid fabric appearance is still not as effective as when combinations of materials.

Installation of suspended ceilings in plasterboard

Mounting tension ceiling in plasterboard ceiling creates the structure in several levels, and black and white games provide an opportunity for a variety of design development. In addition, the combination of GCR and PVC obtained in respect of the cost is cheaper than solid vinyl fabric.

To begin, you will need to prepare a frame of metal profile for sheet material. To set this level, which will be located drywall, and is drawn contour future construction on the ceiling. To the major surface in accordance with the markup loop attached UD profile. On the sides it is cut in 5 cm and attached to the surface. Where the wall will be applied GCR also attached UD profile.

Under future oil paint design is necessary to reach a strong thread. It is fixed on the screws, they must be screwed to the wall at the bottom of UD-profile. To connect with the web design PVC, CD profile should be installed on hangers on a horizontal plane.

CD-profile put in the UD-profile - he had to get to a "virtual" bend, fixed to the suspensions, which is basically the ceiling is already fortified with the help of UD profile. Leveling is performed on a thread profiles.

Clipped another UD, we put on the cut ends of the CD-profiles. It remains to combine vertically prepared sized upper and lower profile. Cut pieces of the profile CDi UD- embedded in the top, the bottom corrects the lateral webs and is fixed profile lower plane. After that, we proceed to the frame plating of metal profile sheets GCR.

And in this article about the plasterboard ceilings with lighting.

To perform the installation of the FCL, desirable helper invite. Lifting and screwing sheet alone, it can be easy to break. To strengthen the sheets of material on a metal frame, it is necessary to have the necessary expertise - only then it is possible.

for fixing you should choose self-tapping screws for metal 25 mm in length - they should be every 30 cm heads of the screws have to be screwed into the surface so that it did not prevent the putty, but also so as not to damage the screw head paper..

vertical sheets of fasteners is performed without cutting the figure. Later, when the material is mounted on the frame, it is cut with a hacksaw. Vertical stripes are cut according to the size and attached to the frame. If you need a vertical bending too steep and curved bands conveniently does not work, it is necessary to slightly trim the paper to the side where the convex curvature. Better just to cut out the desired holes - for lamps, for example.

that angles shpaklevanii we obtain the expression more precisely, on the outer part of the design can be adapted perforated corners.

Photo: Installation of a stretch ceiling at drywall.

Here you clearly see how the installation of a combined ceiling.

We must start with the profile of the carrier assembly; trimming it should be carried out with the utmost precision, to get a smooth beautiful fold. When a profile is properly fastened, it starts stretching canvases. The air should be heated to 60 degrees. Tucked into the profile of the web - centimeter by centimeter, then the room must cool down without any ventilation. Wherein the film returns to the original state, and pulling the lining.

Photo: design combined suspended ceilings made of plasterboard.

And here is an article about how to make plasterboard with their hands.

Http://ru-house.net/stroitelstvo/fundament/ Here you will find many more informative articles about the foundation for your home.

Combined with drywall suspended ceiling when combined in the composition give as a result a great and interesting mix of different structures. If the experiment with shapes and colors, great opportunities - design finds in this regard is truly magnificent.

See inaccurate, incomplete or incorrect information? You know how to make a story better?

Do you want to offer to publish the photos on the topic?

Please help us make the site better! Leave a message and your contacts in the comments - we will contact you and together we will make the publication better!

Additional mortgage under the drywall for ceilings is a must. It makes the surface perfectly horizontal, which allows users to secure good plaster molding. Stretching ceiling can not worry that it will break. Importantly, do not forget to do the shaking of the walls of plasterboard.

On the issue of embedded parts under the drywall. If the asker was referring to the walls sheathed with sheets of drywall, the unit embedded parts at the site of attachment of the mounting profile for stretch ceiling. In practice - this is the profile of a horizontally mounted ceiling at the level of the ceiling arrangement. In this case, the mounting profile is fixed to the wall with anchor plugs and screws to mount the profile sheets of drywall.

Tell me if you need a mortgage to make drywall fasteners to hold the stretch ceiling?

I believe that such composite structures are already fading. 15 years ago, when they began to make such polotki, they were all the rage. Now the fashion changed, the combination of drywall ceilings, all of these multi-level pololki occur less and less. Designers and people with good taste back to the perfectly smooth, matte painted polotkam. Either stop on something one either on plasterboard (not multi-level and flat) or matte stretch ceiling. Please note - it is matte ceiling, as a classic for all times. Glossy ceilings are very specific and some cheap interior, the same applies to all kinds of imitation of the starry sky and clouds.

Apparently, Ludmilla come across people who are just too lazy to create anything and they go the path of least resistance. (Smooth ceiling, it's so elegant, and above all masters strain is not necessary).

With the combination of drywall ceilings bet on interior decorative features can be fully entrusted to the ceiling structures. The play of light, colors are so interesting that the remaining finishing facilities can be quite concise.

Combined the ceiling drywall and tension (see photo). How to make a combined ceiling

Until a few decades ago, decoration ceilings did not cause any problems in home owners: they simply bleached or dyed in bright colors. Today, a huge number of modern finishing materials to create the most incredible ceiling structures, which our grandmothers could not even dream of.

Combined ceilings, photos which are increasingly appearing on the pages of publications on design, today the complementary structure of the drywall. This combination looks very stylish and original. This method of registration allows you to create complex shapes with interesting background and original lighting, thus underlining the interior of any room. Today it is a very common technique in domestic furnishing - combined ceilings (plasterboard and tension), a photo which you can see in this article.

Advantages and disadvantages of the construction

According to the designers, so complex design looks a winner in almost any interior. A combined ceiling (plasterboard web tensioning) has several advantages, among which we highlight:

This method can create custom designs having a frame with tensioning Plasterboard coated inside intricate labyrinths of GCR, complex shapes, which can be framed by sparkling, glossy, matte or mirror film.

The method allows the use of different types of lighting. Suspended ceilings have virtually no restrictions on the choice of lighting devices, in contrast to the tension. Because high-power lamps can be mounted in a box made of plasterboard.

Combined ceilings, photos which have already been placed in the textbooks on design, good by the fact that, using different colors and textures of materials, as well as spotlights, you can divide the room into functional areas (recreation, work).

This design will help you easily hide the pipe, wiring and ventilation ducts.

Longer lifetime

With proper installation and care combined ceiling will serve you for a long time: at least twenty years. You do not need to update the finish as often as in the case of the whitewashed, painted or wallpapered surface. To install such a design not require perfect alignment of the base surface.

Are there any disadvantages of the ceiling?

Undoubtedly, some disadvantages such coverage is. They are significantly less than the merits, however, they should be taken into account when planning a renovation in the house. The disadvantages of this method include:

Almost any two-level design takes up about 10 cm height of the room. Is no exception and the combined ceiling. In addition, if you intend to point lighting, even for the first level it will require at least ten centimeters. Therefore, there can be no question about the installation of the ceiling, for example, in the Khrushchev.

Quality stretched canvas and sheets of drywall, profiles, will cost much more expensive than a two-level combination of drywall ceilings (photo you can see in the article).

Temperature and humidity

PVC and fabric tensioner plasterboard is operated at a certain temperature and humidity. If these figures are significantly higher than the norm, then the material can be deformed.

Variants of the combined ceilings

The combination of suspended structures made of plasterboard and stretch canvases on the ceiling with proper choice will help you create a beautiful optical effects. In this case, a variety of options available from both hidden and open lighting.

So, we present you the most popular options for the combined ceilings of plasterboard and stretch fabrics.

  1. Around the room of plasterboard construction box. PVC fabric in this case is attached inside the box, the dimensions of which may vary. However, there are certain rules. If you need to visually raise the ceiling, emphasizing the beauty of the paintings, then the GCR panel made thin. Excellent visual effect is achieved when the inside of the box mounted spotlights.
  2. An oval or a circle in the center of the ceiling is a good alternative to the usual Plasterboard rectangle located on the perimeter of the room. Inside mounted tensioning the canvas. Such a combined ceiling often simulates the daytime or the night sky. However, this ceiling is not suitable for a small room: it will seem even smaller, since all its angles are sealed with drywall.
  3. "Tabletka9raquo; - this is an interesting ceiling design. gypsum circle is based on the center of the ceiling. Here is mounted chandelier. All the rest of the space occupies a stretched canvas. A variation of this design can be considered a "circle within a circle." In this case, the perimeter of the room is installed an additional duct of plasterboard.

Before you can create a combined ceiling, you must vacate the premises on the furniture, lift curtains and drapes, lighting and paintings, insulate the wire ends, lay a film of the floor.

Preparation of the base surface is the same as before installing any hanging or tension structures:

  • removed old cladding layer;
  • spatula clean a loose plaster;
  • obscure large gap filler based on cement;
  • primed coating.

Necessary materials and components

To set the frame of drywall you will need:

Combined ceilings in the hall (photo we posted in this article), bedroom or other living room can be made of conventional drywall. If work is carried out in the kitchen or in the bathroom, then give preference to gypsum plasterboard. These sheets have additional silicone pellets and antifungal additives having increased water resistance.

To create the tension of the structure will need:

  • Aluminum baguette;
  • shovel for filling the web;
  • fasteners, fixing plasterboard to baguette;
  • heat gun (for one-time use of its better to rent).

Now you need to choose a web of material - fabric or film. The first - more durable, not too afraid of changes in temperature, the film is a huge variety of attractive colors, textures, increased moisture resistance.

Yes, before you start installation work, it is necessary to create the desired circuit design on paper. To this end, the following guidelines must be met:

  • measure the length of the walls, the height of the corners and center of the room;
  • noted in Scheme height of the first level (box plasterboard) and the distance between the tension blade and the base surface;
  • applied to circuit drawing boundary between the two layers and fastening the guide line carrier profiles with a step 60 cm (longitudinal) and 40 cm (crosswise);
  • Mark the location of hangers fixing and laying communications.

After that, all the lines of the drawing are transferred to the walls of the ceiling. Remember that how accurately you apply markup depends on the further course of the work. According to the planned lines much easier to set up the frame. For the application circuit using the ceiling otbivochnogo cord, water or a laser level roulette.

If drywall border and stretch ceiling is shaped like a circle, then at the ceiling it can be transferred by means of the screw screwed into the center, which is linked to a string of the desired radius with fixed at the end of a pencil. To apply curves, it is necessary to make the blank of cardboard and cut around it on the ceiling.

Design combined ceiling may be different. Often the selection of a suitable option depends on your imagination and skills (if you plan to install it yourself).

The first step is to make sure that the guide profile holes for fasteners. Their step should be from 0.3 to 0.4 meters. If not, you will have to use a drill and make them their own.

Attach a lower edge profile to start a pre-applied marking lines. Drill holes at the marked locations to fix and secure the support section on the perimeter of the room using a flared wall plugs.

On the contour border tension and the ceiling surface of the base install guide profile. If it needs bending, it is necessary to make cuts on the opposite side and bend it in the right direction. The marked locations are fixed suspensions.

Now it is necessary to pull the nylon thread for ceiling profiles and insert them into the guide. Secure the hangers. At the ends of the load-bearing profiles must be attached clipped guide. He must follow the contours of UD profile, fixed to the ceiling exactly. Prepare sections of ceiling profile. Their length should match the height of the box of drywall. On the one hand cut the side portions.

Connect the lower and upper guide profiles. To do this, cut the top must be inserted into the guide profile and screw the bottom plane, which was formed after the removal of the jumper.

After installation of gypsum framework should address the laying of communications. Wires were placed in a plastic corrugated pipe and fix it to the base surface, leaving conclusions in those places where the planned installation of lighting fixtures. These works are carried out after disconnecting the electricity in the room.

This work should be performed with an assistant, because the drywall - a pretty heavy stuff, and to cope with it is very difficult to mount. The first sheet is fixed in the corner of the room. If necessary, onto a sheet applied on a template contour and the necessary parts are cut. Cap screws to delve into the material, but not too much, so as not to tear it. The second sheet is attached on the remaining half of the profile, which is fixed to the first web.

Between the wall and the plasterboard is necessary to leave a gap of about 0.5 cm. In the same way the whole area sheathed. Now you can attach drywall to the vertical part of the duct. On curved sections of its bent, which makes shallow cuts on the back side.

After frame plating must glue joints between the sheets and the wall serpyanku ribbon. The gaps and fixing points are applied putty using small spatula. Lap papered vertical and horizontal of the glass-box. In areas of overlap office knife make incisions and remove the excess.

It's time to make the holes for the fixtures. To do this you will need a drill with a crown. Shpaklyuem surface finishing layer, not thicker than half centimeters. When the composition is completely dry, smooth out its fine-grained sandpaper.

Remove from the surface of the vacuum cleaner or dry cloth dust. Finally, apply a top coat. Typically, the combined ceiling covered (plaster part) acrylic composition.

Experts recommend choosing a film with harpoon attachment: it is considered the most reliable. Mark on the vertical part of the leaf level of the constructed box placement. Along this line, attach a baguette with step 7 If you plan to see the curved design -. To make cuts profile, strip of sandpaper or a file and bend in the desired direction.

Heat gun to warm the room 40 ° C and expand the canvas. If it is glossy, then use gloves to no traces. The cloth should not bring close to a heat gun - dark spots may appear on it. When the room is warmed up to 60 ° C, harpoon webs base angle (which is the producer) tuck prints. Just fixed diagonally opposite corner, and then the remaining two.

After that you should start tightening in a baguette harpoon at the level of the perimeter. Then heat the entire surface of the heat gun. Do not worry if after installation you will find wrinkles on the surface - they are easy to smooth, warm low-quality land again.

Create a combined structure of the plasterboard and the tension cloth is not easy. This is a laborious process that requires not only theoretical knowledge but also practical skills. We hope that the above suggestions and photos to help you cope with this work and perform it efficiently.

Features combined suspended ceilings: in the interior photo

Stretch ceilings are perfectly combined with the suspended structures of plasterboard Modern technologies allow to choose any type of coverage today, which will be a great addition to the overall interior style. The most popular stretch and suspended ceilings. Very often consumers confuse the two types of structures. Before you make your choice: Ceilings suspended ceilings, it is better to learn about the advantages and disadvantages of each type and choose the best option. It is important that the ceiling is perfectly suited for the overall style of the interior. To do this from the ceiling views need to decide before the start of repair work.

The main differences of stretch and suspended structures

If necessary, make repairs, many are faced with the choice of ceiling finishes. Many simply do not understand its forms, so to choose a suitable can be quite difficult. To avoid a long search, you can pre-determine the type of structure.

Today popular stretch and suspended ceilings. They have a number of similar and different features to consider when buying.

To install suspended ceilings require less time than hanging

These types of ceiling coverings have become popular thanks to quick and easy installation. Reliability and practicality. A ceiling of choice depends on many nuances. It is influenced by the total area of ​​the premises, the material condition and the taste preferences of the owners of the premises.

The main differences ceilings:

  • Installing a suspended ceiling will take longer than the mounting tension.
  • Installation of a stretch ceiling does not take more than three days.
  • Suspended ceilings easier to install. With their installation, everyone can cope on their own.
  • To install suspended ceilings better to invite professionals.
  • Tension ceilings require minimal maintenance.
  • Suspension in case of damage can be repaired partially, but the suspended ceiling will have to completely remove.

Construction of suspended ceilings are more expensive. Although today the cost is greatly reduced because of the great popularity. However, based on the calculation of the life, the cost can be considered even less.

Combined ceilings: combining options

Today popular combinations ceilings, it is a web of different materials that combine together. Thus, it turns out the original design of the paintings of different color and even texture. Such a ceiling can be made up of various types of materials joined together.

A combination of materials to perform single-level and multi-level constructions of suspended ceilings.

Very popular combination ceilings

To combine the use of different kinds of PVC film: matte, glossy, satin. Also use a combination of fabric and film webs. paintings combinations are used for different kinds of structures: straight and curved.

Options for combination of paintings:

  • Suspended ceiling and drywall;
  • Suspended ceiling and mirrors;
  • Suspended ceiling made of fabric and PVC.

By combining colors is important to observe the rule of harmony. It is not necessary to use a combination of bright colors too. The color of the ceiling should be combined with the overall decoration, furniture and decor items.

Diverse design False ceilings

Before making a final choice in favor of tension or suspended structures, it is important to explore options for their designs. Namely design and its combination with the overall style of the interior will be the deciding factor. In order to deal with options, you need to become familiar with the two types of structures.

Tensile structures are divided into two types: film and fabric. Hinged structures may consist of tiles, strips, boards, drywall.

The design of the ceiling can be combined in a variety of materials and colors

Design of stretch fabrics can be quite varied. It may be formed in a single color or several colors combined. version printing any desired image is also available.

Suspended ceilings have less choice. They may be in the form of plates of different colors, or lining strips. The most popular for the decoration of rooms are sound-absorbing panels.

Beautiful combination of stretch ceiling

Due to the large selection of materials tensile structures can be variously combined. This allows you to arrange the room stylish and original. These types of designs used to decorate the ceiling in the house, apartment, restaurant and concert hall. To imagine the future structure, it is necessary to determine the option combinations.

First you need to determine the type of system. It can be multi-level and single level.

Interestingly it looks suspended ceiling, combines contrasting colors

Multilevel systems involve creating multiple levels. They can go one by one, creating beautiful swings. Such ceilings allow you to create original lighting system.

Embodiments combination sibling ceilings:

  • Connect a straight line;
  • The compound curve.

Widely popular today use a combination of different materials. For example, a combination of suspension and tensioning structures. Design involves creating beautiful monochrome and color designs. Today in fashion and contrasting combinations. They need to be careful - a contrasting color must be harmonious, otherwise the ceiling will tasteless.

Two-colored ceilings (video)

Today, in a fashion stretch and suspended ceilings. Most of their choice depends on the design and the combination with the overall style of the interior. The choice of design can also affect the condition of the ceiling, the size and shape of the room, the amount of allocated funds. These coatings are species of common and distinctive features, that you should know before you make your choice.

Leave a Reply

Your email address will not be published. Required fields are marked *

4 + 2 =