How to cut off the ceiling moldings

How exactly cut angle ceiling skirtings

Beautiful and accurate edging ceiling hides joints Mezhuyev coatings and is an additional element of the room decor. But to ceiling moldings look really beautiful, quality should be able to join his corner joints.

How exactly cut corners ceiling moldings, can be found in our article.

The first way - with the help of Miter

Professional miter box with hinged hacksaw

Miter usually appears in the form of a tray with vertical holes hacksaw. It can be made of wood, metal or plastic. This tool is the oldest and simplest tool carpenter, designed for cutting pieces of wood at an angle of 90 ° and 45 °. There are such kinds of devices for professional work, with swivel mechanism, in which a cutting tool can be rotated and locked in any position.

How to cut off the ceiling moldings

Ceiling angles are divided into internal and external, the method of joining them is a little different.

If necessary, you can make miter box with his hands. This will require three cropping of plywood or boards of the same size. At first they are applied in the form of an inverted "U" and make the corners of the layout. Then markup cut slits under hacksaw almost to the bottom, and board curl.

  • We are doing the right measurements.
  • We set the bar in skirting miter box so that it exactly matches the position of the accommodation on the ceiling.
  • The plinth must be firmly pressed against the opposite wall of the miter box. We hold and pressed his free hand.
  • Put the saw at an angle of 45 ° in the hole and cut the part.

  • Adjacent parts to be cut in the same way, only in a mirror image, as shown in the photo.
  • When cutting softer materials (PVC, styrofoam) using hacksaw blade or conventional construction. Then the work will be neat and smooth edges.

    • Measure the length of the plinth from the nearest wall to the outside corner, is left on the wrong side of the line with a pencil, mark the desired length. It should be remembered that the edge (the upper part) should go a little bit out.
    • Skirting miter box is moved in and cut.
    • Adjacent bar is also necessary to measure with the stock and cut in mirror image to the first part.

    Try on ceiling moldings: dock parts should be perfectly flat. If the result is not achieved, and at the junctions have bumps, you can trim the edges with a knife to the usual perfect docking.

    Check flat dock

    The video is well described all the details:

    The second way - without additional tools

    For the inner corner you can use the easiest way to a perfect docking - by marking on the ceiling. Another example of how to cut a beautiful and smooth angle.

    1. Quirk applied to the ceiling, tightly pressing it flat to the corner edge.
    2. Draw a line along the long side of the plinth on the ceiling.

  • The same effect with the adjacent doing a part on the other side.

  • Mark the point of intersection of lines.

    That will have an even angle -45 °, if you draw a line from the intersection point to the edge of the part. Note that the given method of marking works only with perfectly flat corners.

    With a good eye and accuracy of hand actions, you can use a self-made template that resembles imitation Miter. To do this, take a thin plate or thick plywood and draw a layout as a horizontal rectangle. With the help of a protractor point 45 ° on the right and left side of the rectangle. Draw a line connecting the opposite edges.

    Now you can cut off the ceiling moldings using this layout. Actions are simple and similar to the above description in the first embodiment. Only part of the ceiling is not necessary to insert and overlay at the picture and combine hacksaw markup layout.

    Special accessories for attaching

    Installing ceiling moldings, you can work around the issue, as the cut angle side. In a situation where you do not want to cut anything, if you are a woman and enjoy the beauty, not carpentry work, you can go the other way. We advise to choose for their finishing plinth, to which the store you will find the right part of the figure, covering the joint. Such a method will save time and effort.

    As pokleit decorative ceiling moldings on the ceiling. A method of gluing a decorative cornice by means of glue, sealant and filler. How to make a straight angle on the ceiling.

    Thank you that you have shown great!

    Such pests builders kick up the backside. Upload videos without embarrassment. "0" professionalism. "Then I made a mistake ... .tut not so ... well, okay ..." master class "with your finger in the income statement" (((

    thanks pologlo, given the fact that I'm doing it 1 time and she is not having any experience completely.

    How to make the house

    Site search:

    How to trim the ceiling moldings in the corners at home

    Ceiling moldings called is narrow decorative distinction between the ceiling and adjacent walls.

    They are very easy to mask the joints of the walls and ceiling, especially if they have a different structure and are made not too gently.

    Its presence makes room design more precise and complete.

    People often wonder how wisely and carefully decorate the room ceiling moldings?

    This is especially true for those cases where the homeowner prefers to repairs carried out by their own hands.

    To do this correctly, it is important to comply strictly with existing guidelines and rules of painting and decorating. And then the result will please you.

    In order to hang the ceiling moldings, even the inexperienced repairmen does not arise difficulties. Excites them something quite different: how to trim the ceiling moldings? In fact, almost every room, no matter how intricate the shape it was not equipped with the angles.

    And some elements of the plinth should be nice and smooth docked in these inner corners. And especially in the areas of complex configuration and pomudrit have over external corners. Try to figure out what to do in each of these situations, and how to cut the desired item with the help of available tools.

    Materials baseboards and cutting techniques

    First of all, try to determine from which can be manufactured quirk, and what a particular material is best cut.

    On sale today can be found products from foam (PVC), wood, polystyrene and polyurethane.

    Perhaps one of the cheapest are the plinth of the foam is brittle, soft and brittle material.

    Even fingers can leave dents on them, they are easy to form wrinkles and blemishes. Trim beautifully and smoothly from corner plinth based on polyvinyl chloride is quite difficult.

    An inexperienced master a large number of purchased material can go to waste it is for this reason. Also, this polymer has a high electrostatic properties, which explains its ability to collect dust.

    Cut a plinth it's best with a hacksaw or a sharp knife construction.

    Products made of styrofoam also inexpensive, although this material is more durable analogue conventional foam.

    It is treated as a sharp instrument.

    Plinth of extruded polystyrene are a little more expensive, they are a bit denser and harder to cut them. But they are much less crumble and break.

    Therefore, to cut them more convenient and easier. For this purpose it is convenient to use a hacksaw or a sharp knife.

    Polyurethane skirting ceiling are presently, perhaps, among the most expensive.

    But they justify their cost: moistureproof, quite strong and dense enough elastic.

    Situated above the cooker plinth can be deformed and even a little crackle.

    They are perfectly cut with a special knife, without forming chips. But these products are very sensitive to temperature changes.

    Wooden plinth to ceiling - it's quite heavy and dense products, solid and durable.

    They respond well to the treatment of special small-toothed hacksaw. You can also use a reliable Hacksaw. So how do you cut the ceiling moldings right?

    Note that each master has an opportunity not to pore over the fine cutting and fitting corners.

    It suffices to measure the desired length of the blank and to cut it at right angles.

    All defects and flaws hide this special item. But such a convenient way to take advantage of does not always work, as the standard size of the factory angles may differ significantly from the size of the plinth.

    These corners will be allocated their disparity, and it will look not very neat. But if the design space and dimensions allow preparations to use this method, you should not neglect them.

    But those who have to use one of the ways to trim ceiling moldings, keep the following tips.

    Trimming using stuslo

    How exactly trim angle ceiling moldings with it?

    Miter is called a simple tool used by carpenters. With it, the workpiece can be cut any desired angle.

    He represents a normally wooden, metallic or plastic tray, on which are made for cutting angle of 45 ° and 90 ° special vertical slot.

    There are complicated construction, which to the mentioned angles plus also has a hole for a 60-degree cut.

    For professional work produced a special miter box. Its turning mechanism allows to fix the cutting blade relative to the workpiece at any desired angle.

    Cooked plinth is applied to the ceiling, delayed desired length.

    Then this is the strip is inserted into the miter box exactly as it will be located on the ceiling. It needs to be pressed against the far wall of the device. In this position, the plinth is held with the left hand.

    Handsaw web must be in a position such that its angle was 45 degrees, and the maximum grip to draw it closer to hand. Trying to avoid pressure on the saw, carefully cut the workpiece.

    Further, in the plinth must be cut strikers. It is also located on the far wall of the instrument, holding and cuddling, this time with his right hand.

    A similar situation handsaw previous procedure - it approaches the handle arm at an angle of 45 degrees. Skirting trimmed.

    Then the ready, already cut strips dock - checked the accuracy of the fit. It is believed that, for better orientation, the manufacture of the inner corner, cut it is better to start from the front of the unit. Places slices usually have more customized file.

    The right thing to observe more accurately the dimensions, first begin to mark up an internal angle, and only then move on to the outside.

    Otherwise, it may happen that the entire length of the strap is not enough.

    Planck is applied to the ceiling, the size made the basting. Hold down the left hand is pressed against the ceiling moldings very near the wall, hacksaw handle moving closer to hand. The blank is cut.

    Mounting plate is pressed against the nearest wall, while she holds your right hand. Handsaw web should be at an angle of 45 °, the tool handle approaches the master hand. A piece is cut workpiece, the angle accurately dock.

    Such processing using edge parts of wort is good in cases where the angle between the walls smooth and straight (90 °).

    If his performance is poor, you should use another method.

    How to cut the ceiling moldings without Miter?

    In all other respects with the help of this method you will be able to identify the angle of cutting even more accurately than others.

    When a plinth is applied to the intended place of installation, all dimensional deviations and inaccuracies visible and immediately taken into account.

    First you need to take a couple of billets, then cut them at right angles. Abutting end strips perpendicular to the wall, apply a bar. Outlines the ceiling line along the contour of the floor. Remove the first bar, and then the same end abutting a wall is applied reciprocal bar. Similarly, we note the contour line.

    The intersection point of two lines is a separate mark, on which the workpiece is cut off. Each strip is applied to the surface again, both marks the point of the future cut. From these points to the other end to draw a line skirting strips. Skirting cut off by the previously made basting gently sostykuem, located in the place of their installation.

    Such a method enables more accurate processing interior angles.

    How to make a pattern miter box with his hands

    If you do not miter box, not necessarily to buy a tool for single use. Template with similar functions can be done independently.

    For this purpose, wood, paper or cardboard cut applied the desired angles.

    Next, you need to draw a pair of parallel lines to find the center, then use a protractor to measure angles of any given magnitude.

    Such a method is particularly useful in that, by using it, it is possible to delay the angle of any size, even greater direct.

    Method of processing Baseboard workpiece using a homemade instrument practically does not differ from that of the original. Planck is pressed against one of the parallels, then hacksaw set at the desired angle, and cut.

    How to cut the ceiling moldings properly. important stuff

    The measurements required for trimming skirting on the ceiling should be done in a special way.

    To determine the level and the internal angle, the length should measure from the corner. To mark the outside corner must take into account that the deep space will act as a plinth for a distance that is equal to its width.

    Rods skirting it is not desirable to fix until the examples as will their current location and clipped back plinth.

    Only after a perfect convergence in the corner of the two mounting plates can begin their installation and mounting. If you are working with polyurethane or wooden plinths, defects and flaws can be fixed nail file or a file. To fit the product of the foam should be armed with sharp knife.

    If after completion of plinths is at least a small slit, do not rush upset - it is easy to seal the conventional filler.

    Trim precisely and accurately ceiling moldings is not too difficult. But in order to get at least a little skill, try to pre-train on small workpieces.

    ceilings

    Ceiling moldings performs not only a decorative function, visually separating the wall from the ceiling, but also can hide under a crossroads of different finishing materials of the ceiling and walls. Not every interior design involves the use of ceiling moldings, but more often than the general look of the room seems to be incomplete without it. The mounting of the element - fillets - no big deal, almost all types of plinths are mounted on the glue. But the question of how to cut the ceiling moldings in the corners of rooms, can put many at a standstill. After all, even in the simplest room there are internal corners where the ceiling moldings and trims must be exactly nice dock. A more complex configuration of the room and will have to dock the plinth, performing the outer corner. In this article, we will consider various options how to cut a ceiling plinth with the help of available tools and without them.

    To begin to deal with the issue than to cut ceiling moldings, the answer depends on the material of construction of the fillet. At the moment, selling ceiling moldings from polyvinyl chloride (PVC), polystyrene (styrofoam), polyurethane and wood.

    Ceiling moldings made of PVC They are the least expensive. They are easily formed dents and creases, which can not be eliminated, so the product has to be discarded. Their disadvantage is the electrical charge - the ability to attract dust. They can be cut with a knife or a sharp construction hacksaw.

    Ceiling moldings from expanded polystyrene also belong to the cheapest. This material is very fragile, easily crumble during processing, so it is necessary to cut the foam board with a sharp knife or hacksaw, without making too strong to press efforts.

    Ceiling moldings made of extruded polystyrene foam slightly more expensive than polystyrene foam, their denser and harder to cut. However, they are less crumble, so they are easier and more convenient to work with. Construction cut knife and hacksaw.

    Ceiling moldings of polyurethane They are the most expensive at the moment. They are durable, moisture resistant and elastic, easy to cut with a knife, and building do not crumble. A disadvantage of polyurethane moldings is their dependence on the temperature changes. For example, on a gas stove polyurethane moldings acquire permanent deformations begin and slightly crackled. If you try this process baseboard or trim, it can be bent or otherwise deformed.

    Wooden ceiling moldings are dense heavy products that can be cut with a hacksaw only, preferably with frequent small teeth. You can also use a blade for metal.

    Before proceeding to the enumeration of the ways how to cut the ceiling moldings, it should be noted that it is possible not to cut moldings with extreme precision. In commercially available special corner pieces, into which the edge of the plinth. In this case the bar skirting sufficient undercut at an angle of 90 °, and the corner member hides all the flaws. But this method is not always used as corner pieces slightly larger size plinths themselves, so the corners of the room will be allocated on the general background. Sometimes it can look nalyapisto. Nevertheless, if the design space allows the use of corner pieces for skirting ceiling, it makes sense to take advantage of them. Further instructions will be useful to those who still decided to precisely cut the plinth at a predetermined angle.

    As cut angle ceiling moldings via stuslo

    Miter box - a simple carpenter's tool to cut the workpiece at the required angle. In most cases, the tray is made of plastic, wood or metal with vertical slits for cutting at an angle of 90 ° and 45 °. There are also more complicated constructions stuslo - cutting angles of 90, 60 and 45 degrees. For more professional work is used miter box with turning mechanism, where the saw can be fixed at any angle to the workpiece.

    As cut ceiling moldings via stuslo - internal angle:

    • We put the baseboard to the ceiling, measure the desired length.
    • Then set the plinth bar in miter box so that the position matches the position of the ceiling skirtings.
    • Planck plinth should be pressed against the far wall of the miter box.
    • Keep skirting the left hand.
    • Choosing a position handsaw, when the angle is 45 degrees and wherein the handle handsaw maximally approaches the left hand.
    • We cut the workpiece without making excessive pressure on the saw.
    • The next step - cutting response plank floor. We set it as the far wall of the miter box.
    • We press and hold the right hand.
    • Choosing a location for a handsaw when the angle of 45 degrees and a hacksaw handle approaches the right hand.
    • Cut the plinth.

    Next we butted cut skirting strips and check the precision of the cut. For a more accurate orientation say again that to make an internal angle should begin cutting from the front of the plinth. Wooden skirting boards after cutting, most likely, will have to adjust the file.

    As cut ceiling moldings via stuslo - external angle:

    • Not to be mistaken with the size, it is better to start with the inner corner of the layout, and then cut the outer corner. Otherwise, it is possible that when the slats may not be sufficient in length.
    • It is necessary to attach the strap to the ceiling and to outline the dimensions.
    • We set the bar ceiling moldings and presses it against the nearest wall.
    • Hold the left-hand and choose a location for the hacksaw at an angle of 45 degrees, when the pen comes close to the left hand.
    • Cut the workpiece.
    • Install the mounting plate to the nearest wall, hold the right arm.
    • Set the saw at an angle of 45 degrees, when the pen comes close to the right hand.
    • Cut the workpiece and butted angle.

    Crop harvesting via stuslo suitable only in the case if the angle between the walls of the even-tempered - 90 degrees. If the accuracy is poor, it is necessary to use other means.

    As ceiling trim angle skirting using markup ceiling

    Partitioning plinth on the ceiling also enables smooth and accurate cut angle. The only drawback of this method is that it is difficult and inconvenient to keep the bar plinth on weight during the cutting process. The rest of the outline for cutting angle thus possible to even more accurately than other methods. By applying the plinth to the installation site, once taken into account all the flaws of the walls and the deviation in the amount of the angle.

    Circumcision angle ceiling moldings:

    • First of all two pieces must be cut at an angle of 90 degrees.

    • Then, putting a first one bar, emphasizing her butt in a perpendicular wall. We draw a line on the ceiling, outlining the contour of the floor.

    • Remove the bar and puts strikers, also emphasizing its end into the wall. We outline the line.

    • The intersection point of the planned line will be marked on which you want to trim moldings.
    • Again, we are putting a turn each bar and they mark a point cut.
    • We draw a line from this point to the other edge of the plinth.

    Cut the plinth on the planned lines, butted them and apply to the installation site. Please note that by using this method is more convenient to cut internal corners.

    As ceiling trim moldings via template stuslo

    Something resembling a miter box can be made if necessary to put the corners cut on paper, cardboard or wood. It is necessary to draw two parallel lines, determine the center and then to postpone the necessary angles with a protractor. The advantage of this method is that it is possible to delay any angle, including 90 degrees and greater. Of course, before the cut angles ceiling moldings, it is necessary to check in advance the angle between the walls using a protractor and measure the corner.

    Methods of cutting the ceiling moldings by drawing a miter box is exactly the same as with the help of the miter box. Skirting the bar is pressed against the one of the parallel lines, then set a hacksaw to the desired angle, which is already planned, and cuts.

    Makeshift tray-miter box with his hands

    Manufacture miter box with his hands and is not too difficult.

    Method 1. Need three wooden planks or boards to be put together in a U-shaped case. Then, on the walls of the box outlines the necessary angles, and a hacksaw cut is performed. The result should be a wooden miter box, which cut the grooves.

    Method 2. Combination and improvised stuslo template with the intended lines. Cutting amenities you need to build something, in what will be convenient to hold the lath ceiling moldings as well as how to keep it on the hard weight. Enough to put together two wooden planks or boards area. On paper it is necessary to draw lines with cutting angles at 45 degrees, or at any other. Is then applied to a corner plinth preform, presses her hand, as described in the usage stuslo technology, the paper with the pattern moves under the region where going to perform cutting, and cut off. In the cutting process are guided by a line drawn on paper.

    Method 3. In an impromptu miter box, you can use anything, everything - that form the corner. For example, a table pushed against the wall.

    Important! Notice the performance measurement to trim ceiling moldings. To identify an internal angle, it is necessary to measure directly on the length of the corner. To schedule an external angle, you must navigate a plinth that will play into the room at a distance equal to its width.

    It is not necessary to fix the ceiling slats skirting boards before the cut mounting plates and an example of their location. Only after two strikers came together perfectly in the corner, you can start to fix them to the ceiling. Minor flaws can be modified nail file or a file in the case with wooden skirting and polyurethane. To fit the foam product will have to wield a sharp knife.

    If suddenly, even after adjusting skirting between them remains a small gap, do not despair, it can be repaired with putty. Trim the ceiling moldings yourself is not difficult. But in order not to spoil a lot of products, better pre-trained on small workpieces.

    but the outer ceiling is not

    but the outer ceiling did not show!

    Related Articles

    © Building portal StrPort 2011-2016. Articles about the repair, construction and building materials.

    Copy information from the site is possible only with permission of the publisher or a direct reference to the source. legal rationale

  • Leave a Reply

    Your email address will not be published. Required fields are marked *

    + 76 = 79