How to disassemble the handle interior door round

How to disassemble the door handle on their own

Doorknob can be called a key element for any interior door. Open any flap, whether folding, hinged or sliding, without such a simple device as a doorknob is extremely inconvenient. That is why the demand for it far behind even accessories such as a latch or a lock. In order to understand how to disassemble the door handle, you need to understand what they are. Usually they are divided into two groups: stationary and pressure

A distinctive feature of the stationary door handles is that they have no connection with the lock. They are usually installed separately, as a standalone device. The sole function of such handles - open and close the sash, holding on to it. They are usually mounted almost anywhere using screws. Appearance of such handles is very diverse, but still the most popular are U-shaped, similar to the bracket, and they are fixed, usually vertically. If necessary, the restriction of access to the room, it is possible to install the roller from the inside latch.

How to understand the stationary handle

Usually, if you have installed a stationary door handle, the question of "how to disassemble the door handle interior door" is not difficult. Since such a device have a very simple and failure are rare, take them off only when there is a desire to change to a newer model. To do this, simply unscrew the screws with a flat screwdriver and remove the handle.

It also happens that the hardware that is mounted on a common pivot member. To verify this, we must hold fast to one of the handles, and the second attempt provernut.Zatem carefully unscrew one of the fragments, the second is then easily removed from the door.

Mechanisms Lever handle a little more complicated. Due to the fact that they have a lever latch requires tight bumping into the door. When there is a depression, the latch plate is biased by a spring, in consequence of which it becomes possible to open the door. To sash can be easily shut, while, when the handle is free, the latch is extended. With this approach, sound and heat insulation becomes much higher, because the flap adjacent to the frame somewhat denser.

In these arrangements there is a possibility of emergency opening. To use it, you need to find a slot, which is made from the front. Then, using any flat object, such as a screwdriver, a door can be unlocked without difficulty.

How to disassemble the door handle push-type

It is worth noting that for parsing Lever take longer. To save it is necessary to adhere to the following plan:

  1. Remove with a screwdriver the screws that hold the cover.
  2. It is necessary to pay attention to the tetrahedral arrangement of the retaining rod. He just cleaned and accessories easily unscrewed.
  3. Remove the second cover and to remove the second fragment together with the axial rod.

Lever mechanisms, in turn, is also divided into categories.

Mechanisms with whole-pallet lining, installation of going through the lock. The irreplaceable role played by the center pin on him, and put on furniture - it should be clearly different from the thickness of the door leaf. It should immediately be prepared to ensure that if it fails, the replacement of the entire mechanism is inevitable.

With separate pads. They can be both with a lock, and without it, the only thing that matters - the value of the key size of the holes and pads themselves.

If it is time to decide how to disassemble a round doorknob, then most likely it had to deal with a pen - Nob. This accessory is usually just referred to as the pressure, but at least they are found in the category of turning. The mechanism of action they have roughly the same, but to the flap opens, turn the Knob. Often these pens have a lock button. When pressed, it will be difficult to open the door from the back side. As the push handles on the front side there is a slot for emergency opening.

To the oil paint does not dry during storage and that it was not formed on the film, put on the paint surface torsion Joc of thick paper i'zaleyte a thin layer of varnish.

"The polyethylene film is harboring a balcony or a greenhouse, before stores by breaking wind twine, stretched on both sides of the interval 10-15 cm."

"In order to work with the concrete mix easier, it usually ADDED lyayut clay, but the clay reduces the strength of the mixture. Add it spoon washing powder based on a water bucket."

"In order to screw the head of which is hidden behind a barrier, does not rotate along with the tightened nut, you need to throw it a few turns of thread or thin wire and gently pull the ends. Due to the friction of the screw is well held in place. The ends of follows the tightening thread can be cut."

"Cut notches birdhouse possible without brace. It is enough to split the front of the board in the middle and cut down a chisel or ax poluotverstiya desired size, and then reconnect the halves."

Wooden plugs for the screws crumble and fall out of ste us. Do not rush to cut a new tube. Firmly tamp an aperture in the wall of the old Caproni stocking. Red hot gvoz dem vyplavte hole of suitable diameter for the screw. Ra nylon alloy will become a solid plug.

"Carpenter's level is not difficult to turn into a theodolite, providing it with sighting device from the slot, and fly."

"To the two strips of linoleum laid end to end, it is convenient to use the self-adhesive decorative film, placing it under the basis of whether noleuma."

"To nail in the correct direction, and do not bend at Zabi Vania in a deep hole or slot, place it inside a tube fixed with crumpled paper or clay."

Before to chisel a hole in the concrete wall, attach just below the piece of paper. Concrete dust and debris will not scatter around the room smiling.

"To cut the pipe just below the right angle, it is advisable to drink a post like that. Take a flat strip of paper and screw it onto the pipe of the sawing line. The plane passing through the chrome-ku paper will be strictly perpendicular to the axis of the tube."

"Tossed a log or wooden beams help with simple sposoblenie - segment motorcycle or a bicycle chain, the complement hook at one end and attached to the scrap homa is on the other side."

"In order to be able to work one two-handed saw, use a simple trick: to rearrange the saw handle from the top position to the bottom."

Cut a piece of slate desired size can be a saw, but it is better and easier to penetrate the nail holes with a frequency of 2-3 cm of the proposed incision line, then break off the slate on the pedestal.

"The best way to glue the tiles to the wall:. To take the bitumen melt and drip a drop of only four in the corners of the tile is glued to the dead."

Shaped openings in the manufacture of curved windows cash Cove is most convenient to cut a hacksaw blade peeled.

"Manufacturing of stained glass - it is a long and difficult can be done quickly imitation stained glass to take this reechki thin rods or rod, is glued to the glass sheet, and then color in the glass and covered with varnish..."

"If the hand is not turned dowels, it can be manufactured from a piece of plastic pipe. This may come and housing shari kovoy handle. Sawed off a piece of the desired length, make a longitudinal incision ny, to about half, and the dowel is ready."

"We know how difficult it is to hang the door, working alone. But enough to shorten the lower pin on 23 mm, and work will be much easier."

"Very solid, dimensional stability and sufficient waterproof coat obtained from Bustilat mixed with any powder - IU scrap, gypsum, cement !, sawdust, etc..."

"If you want to screw into the end of chipboard screw, drill a hole slightly smaller than the diameter of the screw, fill the hole with glue" Moment "(not epoxy!), A day screw screw. Plate does not separate. However, under load the resulting compound can be put only after day. "

"Hooking portraits, photos, pictures in wooden frames with glass are not convenient carnations and using stationery CCW dormancy, bent at a right angle. The buttons are pressed gently wriggle Coy. As compared to the danger of split nails thin frame is reduced to a minimum."

"Tighten the screw in the not so easy to hardwoods. If you prick with an awl hole for the screw, and the screw to rub soap abundantly, after such an operation, the work will go like clockwork."

To save time, the edge of the wallpaper can be cut with a sharp knife, not turning roll. To do this, you must first align the end of the roll and a simple pencil to circle the outside of the border edges. Working with a knife, a roll should be gradually rotated in the direction of clotting.

To carry home a large sheet of plywood or a thin stack la convenient to use iron wire holding a teleconference with three hooks at the bottom and at the top of the handle.

IF you want to saw away round a stick, the job more convenient to just run with the help of a template. It is made of a metal tube with a slot in between. The diameter is selected such that the pattern is free to slide on the stick.

Hacksaw will work better I better if in the middle part of uveln n't ^ 1/3 the height of the teeth.

If the front of the machine Bow saws attach a weight of approximately a kilogram, the work will be easier. Georgia needs to do a removable, so that the saw can be tossed to perform other work.

"The coating resembling wax, can be obtained by painting the surface with diluted white glue. To get the color you want, you need to dilute the adhesive with water tinted with watercolors."

"Make a cover for the blade topora- simple. Take a piece of rubber tubing, cut lengthwise and put on the blade. From coming off it protects the ring, cut from old car mobile camera."

"Do without clamps when gluing wood frames will clothesline cord. It should be put on four short loops on the corners of the frame and two long frame pull diagonally. Angles regularity liruyutsya with sticks, which are twisted middle loop."

"How to silence a creaking floorboard? E between the boards need to drill a hole at an angle of 45 ° with a diameter of 6-8 mm, put in his wooden pin, oiled carpenter's glue, Wed to show a chisel protruding end and putty the surface of the floor."

"To facilitate the scraping floor, covered with varnish or paint, iron its iron through a damp cloth - and there is no easier work than a hundred."

"Small decay on wood can be eliminated as follows: the affected wood is removed from the healthy layer, and then propyl TYVA 10 percent formalin solution after drying and paint over a portion zashpaklevyvayut.."

"Door hinges will not creak, if their time to lubricate - it has long been known rule, but you can do without lubrication It is necessary to make the puck out of plastic tubes and put it on the hinge pin..."

"Of faulty door latch due to breakage of the spring but we can repair so: pruzhish role successfully perform otre straps rubber tube of 15 mm diameter piece of elastic or D zines installed between the latch bolt and housings."

We offer a simple device for locking the window frame in the open position: a wooden or plastic plate in which is drilled a number of holes for the bolt. Plate pitsya credit to the window frame screw.

"Cut in the sheet material may be a large opening about ner: hamstring nail (it will serve axis) and a fragment of the drill (this will cutter) Circumference Vera scheniem cut sheet around an axis.".

"Sawing asbotsemeltny wavy sheet at an angle to the direction of the waves is very difficult. For ease of operation recommend wet leaf with water using wet rags, imposed a two hundred and Ron on the cut line. Soaked asbestos cement becomes considerable but is softer."

"To oil paint does not dry during storage and that it was not formed on the film, put on the paint surface Kru Joc heavy paper i'zaleyte a thin layer of varnish."

"The polyethylene film is harboring a balcony or a greenhouse, before stores by breaking wind twine, stretched on both sides of the interval 10-15 cm."

"In order to work with the concrete mix easier, it usually ADDED lyayut clay, but the clay reduces the strength of the mixture. Add it spoon washing powder based on a water bucket."

"Cut notches birdhouse possible without brace. It is enough to split the front of the board in the middle and cut down a chisel or ax poluotverstiya desired size, and then reconnect the halves."

"Carpenter's level is not difficult to turn into a theodolite, providing it with sighting device from the slot, and fly."

"To the two strips of linoleum laid end to end, it is convenient to use the self-adhesive decorative film, placing it under the basis of whether noleuma."

"To nail in the correct direction, and do not bend at Zabi Vania in a deep hole or slot, place it inside a tube fixed with crumpled paper or clay."

"Before peck a hole in a concrete wall, attach just below the piece of paper. Dust and concrete fragments will not scatter around the room smiling."

"Tossed a log or wooden beams help with simple sposoblenie - segment motorcycle or a bicycle chain, the complement hook at one end and attached to the scrap homa is on the other side."

"In order to be able to work one two-handed saw, use a simple trick: to rearrange the saw handle from the top position to the bottom."

"Cut a piece of slate desired size can be a saw, but it is better and easier to penetrate the nail holes with a frequency of 2-3 cm of the proposed incision line, then break off the slate on the pedestal."

on the foundation waterproofing. Where to buy and ...

Plastic windows at affordable rates to ...

Solid fuel boilers: advantages and wasps ...

Professional care for coating of at ...

Warm and practical home from a bar

2015 © «lsmd» - Russian portal builders.

Copy information from the site is permitted only with reference to the source is indexed.

How to remove the handle from the interior door: the necessary tools, instructions

Any owner would be useful to know how to disassemble the handle on the door, especially of interior. This hardware is severely tested by all the tenants, so someday she will fail and will need to be replaced another. In this case, you do not need to call the professionals, you can cope on their own, thus saving on employee wages. Especially that this case does not require a lot of skill and a bit of skill. the dismantling process can vary depending on the type of pen, but to cause particular difficulties the whole process should not. How to remove the handle from the interior door? Before proceeding to an analysis of the mechanism, it is necessary to find out what species it belongs on the classification. The division takes place according to several criteria. Described below is right for parsing the handle, because it has a classification of design features.

Push. This handle is attached on both sides of the door leaf and has an L-shape. The opening takes place due to the load on the knob, whereupon the tab is driven. The disadvantage of this fitting is that it is very traumatic.

Swivel. The method of opening the same as the pressure in only the tab is driven not by pressing the knob and rotating it. Such models are often not very convenient, because to scroll through her hands should be dry, otherwise they will slip. When replacing a legitimate question arises of how to unscrew the handle interior door.

Stationary. In this pen is no latch. It is fastened with screws directly to the door leaf. Often single- or double-sided, with an axial connecting member.

Parse any of the door handles model is not so difficult, because they have a similar structure.

At the same time carry out the analysis of the hardware is rarely necessary. What are the reasons can cause this? How to remove the handle from the interior door?

The first reason - failure. It occurs most often. Often prone to breakdowns cheap Chinese models, which are not designed for constant and coarse load. If not observed prevention of certain elements, the hardware comes into disrepair. It should be repaired, and sometimes even replace the entire unit.

Another reason - the need for replacement. Each year, the market replenished with new and improved models. In this case, you can choose colors, suitable for interior or put a new, more functional and reliable model.

Repair of the premises often involves changing the style. Do not overlook in this case and the door handles. Therefore, the question often arises about how to disassemble the door handle.

Another reason - a spoiled appearance. If the item is made of poor quality material, then it will soon be visible scrapes and scratches, which negatively affects the entire interior.

How to remove the handle from the interior door push-type? This mechanism is more complicated to dismantle, because there is a pivot axis at the expense of which holds a pen in his designs. He tightened tetrahedron.

The process of parsing the handle must begin with the removal of plugs around. They are fastened with screws or held tightly. They are very easy to be removed by the minus screwdriver.

Further needs a tetrahedron, which will reduce the strength of the rod attachment.

On one side of the door need to unscrew and remove the fittings. Then the second part is removed, which remains the rod axis.

Compliance with consistency and accuracy will help to remove the mechanism without any problems, without damaging the parts and do not create unnecessary trouble.

How to remove the handle from the interior door with swivel socket?

When there is no side of the hole into which you can insert a key or screwdriver in the rotary-type fittings, the elements are separated by hand. Both parts of the handle should be turned in different directions, and gradually withdraw from the thread. One of them would be a pivot. Similarly unscrewed and removed socket screws. When the axis is removed, you can do the following elements - a lock latch or, if there is such a need. When removed decorative pieces, it is necessary to monitor the application of its strength, because overdoing can damage components.

Handle with a lock for interior swing type doors removed as follows.

This will require a key for clamping spring mechanism. Often it is not included in the package with the product, but it can easily replace a nail or other pointed object.

The first step is to remove the decorative plate, which you can simply hook with a sharp object.

Key or the spring loaded push pin a nail by inserting a tool in technological hole, located laterally. At the same time pull the handle and pull it together with the cap.

Further removed decorative flange. For this purpose to hook the latch.

After you need to push the fixing screws on the plate. Then the two parts of the handle succumb to removal together with the axis.

Assemble the back handles for doors round will not be difficult, but all the actions needed to be done in reverse order. First is the installation of the lock, which is fixed the plate is then inserted into the axis holding elements is put on it. Inlays are mounted last. The main thing - do not forget that the first threaded decorative flange, and then later attached the main part of the handle.

How to disassemble the door handle fixed type? They are less likely to break or deform. This is due to its lack of moving parts. Often this type of door handles after removal do not repair and change the whole thing. removing process is as follows:

  1. Unscrewed screws with a screwdriver.
  2. One part is unscrewed from the rod, and the second is removed along with it.

the central core may be absent in such an arrangement, it is much reduces the process. You only need to choose the right screwdriver to unscrew the screws of a certain diameter.

The first thing when dismantled handle latch for interior doors with automatic lock, you must remove the screws with a screwdriver. Next detach overhead elements. Using a wrench to unscrew the rod. Then pull the swivel mechanism coiled spring.

There are several ways in which removed the handle latch for interior doors round shape with a lock. Here are the most popular of them.

Laths need to remove the screwdriver, first with the part where a clamp device. On the next stop is necessary to push and pull at the same time to handle myself.

Next, two screws can be turned out, and then removed of the handle latch.

Then, the latch is pulled out, which screws are unscrewed, after the pawl is released.

Thus, parse any door handle with your hands is not much difficulty.

How to disassemble the door handle interior door: diagram Photo

Handle - certainly an important functional element of any door. Modern manufacturers supply to the market is basically just quality fittings. However, to change the handles on the new sometimes, unfortunately, still necessary. Some apartment owners prefer to delegate the procedure employed by the masters. But since, in principle, the answer to the question of how to disassemble the door handle interior door, is simple, if you wish, you can save money and deal with this procedure alone.

In this article we will in detail and consider how to disassemble the door handle interior door. Of course, photos of the operation to the reader, will also be provided.

Actually she handles interior door replacement may be required in the following cases:

  1. In case of breakage. This is one of the most frequent reasons for the need to dismantle. The mechanism of the door handle with time or due to intensive use, either as a result of ill-treatment of cloth worn. Some of the details at the same time fail, and accessories stops performing its basic functions.
  2. If necessary, the installation of a new model. Technology nowadays are developing very quickly. And so the market periodically appear handles more perfect design.
  3. Repairs in the house. It can also cause the need to dismantle the door handles. After the repair of the interior living spaces are often changed most dramatically. As a result, the design of old pens can make disharmony in design.
  4. The occurrence of scuffs on the most grip. Decorative covering such a core portion fittings due to intensive use over time begins to wear away. Frayed handle interior doors so they do not spoil the overall impression of the interior decoration, of course, and should be replaced with new ones.

Before proceeding to dismantle the door handle, you should, of course, to prepare all the necessary tools. To disassemble this element handyman will need:

  • screwdriver;
  • awl, nail or other sharp and thin metal object.

Actually at the place of work, of course, the need to ensure good lighting. Some elements of the design of the door handles are small. For a small amount of light they can simply get lost.

Variety of door accessories

How to disassemble the interior door handle, we will look at in detail in the article below. To begin with, let us see what, in fact, exist in the market today such a variety of accessories. After all, a way to dismantle the handle depends, of course, primarily on the characteristics of its structure. Modern doors can be supplied to the market with fittings of this group:

  • stationary;
  • turning;
  • pressure.

Also, the interior doors are often equipped with special handles, nobami, closing including a key.

The design feature of this fitting is that in most cases it is not connected with a latch and a lock. Used stationary handle only proper to close the door, and plowing. Fastened this kind of hardware directly to the canvas, often with the help of screws.

How to disassemble the handle interior door fixed

To remove the fabric of this variety of hardware, only need a screwdriver handyman. Disassemble the stationary U-shaped arm as follows:

  • spun screw on the main body;
  • clean handle.

Such a simple technique can serve as an excellent response including the question of how to disassemble a round door handle interior door rod. When removing such accessories as usual (in the form of staples), screws, most often also unscrewed on one side only.

In some cases, the stationary handle may be supplemented by a mechanical latch. This embodiment demountable fittings follows:

  • screwdriver carefully unscrewed the fixing screws;
  • laths are removed;
  • a metal pin of the jumper is removed from the cap;
  • removed handle with one hand;
  • on the other hand is removed tetrahedral jumper.

How to disassemble the door handle interior door: dismantling scheme swivel fittings

Stationary design on the doors are used very often. But many modern interior model can be equipped and easy to use rotary knobs. Accessories of this species consists of the following elements:

  • the knob, rotating around its axis;
  • falevye latch or latches.

the knob rotation angle of such handles is limited only by the latch stroke quantity. The main advantage of this variety of accessories to be compact.

Of course, many domestic masters would like to learn how to make out the interior door handle and such variety. Removing swivel fittings made by the following procedure:

  • the canvas removed laths;
  • a lateral opening is inserted technological sharp end awl or nail;
  • the pin is removed;
  • The property itself is removed from the pen cap.

At the final stage handyman need to hook the latch and remove the decorative flange.

Handles of this species have a T-shape. Fitted with pressure fittings mainly office interior doors. But sometimes they complemented fabric and household models (usually plastic). When you click on a handle of a lever starts to move the lever, causing the door opens.

Dismantling of the push handles begin with removal laths adjacent the lever. To remove the item, you should:

  • press the rotary stopper bracket;
  • pull the shaft and handle.

For convenience, at this stage, you should use an awl or nail. After the plate is removed, you need to:

  • Unscrew the handle parts screws;
  • extract tetrahedral rod;
  • remove the second pad;
  • remove the remaining parts of the handle.

Accessories of this species, in fact, belongs to the class of swivel. However, in the structure of such handles, among other things, is further present keyhole and fixing the button.

Next, let's see how to disassemble the door handle interior door with a latch and padlock. For dismantling such fittings, in addition to the screwdriver, handyman need also a special key to stop. Last usually comes with the pen. Nob dismantled as follows:

  • poddevat screwdriver and remove the cover;
  • a stopper for opened or awl press nail;
  • knob removed;
  • removed from the handle spun two screws;
  • remove the liberated parts of the structure.

At the final stage unscrew the screws retaining the latch. Next, you just need to remove the last of the fabric.

Thus, we'll have figured out how to disassemble the door handle interior door with a lock, conventional rotary, push or stationary. Dismantled all these varieties of accessories, as you can see, quite easily. However, to carry out the disassembly procedure, of course, it should be possible accurately. In particular careful handyman to be using a screwdriver or an awl. Torn, these sharp tools can be very easy to damage the decorative surface of the door leaf. And this, in turn, of course, a very negative impact on the appearance and the entire premises in general.

Leave a Reply

Your email address will not be published. Required fields are marked *

+ 43 = 44