How to regulate the plastic windows to

How to adjust the plastic windows independently

Nowadays, people are actively replace the old wooden frame on the euro windows. Convenient modern designs collected in plastic and metal, are reliable and durable. They just closed and provide a high level of thermal insulation. Knowing how to handle plastic windows yourself, you will be able to solve some problems without the involvement of specialists. The correct and safe setting euro-design requires compliance with some rules which, however, this is no big deal. Read on and learn how to act in any given situation.

What problems can be resolved by yourself

Like any other mechanism, plastic window may be damaged. Correction of serious damage is better left to professionals. Minor problems you can fix your own hands. Independent basic repairs that can fulfill any man without involving the master includes the following works:

  • replacing the failed handle;
  • eliminating jamming of the handle in the open position;
  • Update lubrication mechanism of the handle;
  • eccentrics adjustment to eliminate air leakage under the seal;
  • setup constraints;
  • replacement of worn seal.

Step by step instructions on setting plastic windows

Adjustment of plastic windows does not mean absolutely nothing complicated. The main thing - to listen carefully to the valuable recommendations of experts and with the utmost care to follow the instructions. The following sections of this article you'll find detailed instructions to help you understand how to adjust the windows to optimize their work. Save or write down for yourself these basic scheme of repair, so as not to get lost in cases of force majeure.

When winter comes along with the freezing cold, many owners of flats and houses can not help thinking about how to adjust the plastic window for the winter. To do this, you need to change the position of pins (special pieces of metal fittings) to increase the degree of pressing of the flaps. It sounds scary, but in fact, this problem is not particularly difficult. So, make a note of how to adjust the double-glazed window, so as not to muzzle the street in a severe frost:

  • Make sure that the box design is equipped with special cams, controls the degree of clamping wings (if not, you can not switch the window in the "winter" mode);
  • Find cams on the inside of the wings (they are located exactly in the middle and on the edges of the wings);
  • pay attention to the current state of the eccentrics, and then turn each at 40-50 ° clockwise;
  • gently close the window to feel the stroke of the handle;
  • if you notice that this movement is given with little effort - it means that the seal is pressed more strongly than before, and therefore more reliably holds back the air;
  • Otherwise, turn in a counterclockwise direction until you get the desired result.

For correct and safe switching between "winter" / "summer" use a special screwdriver. Turn eccentric to the maximum extent sash clamping is not recommended. Strong load lead to the destruction of the sealing material, due to which inevitably deteriorate insulating characteristics of the IG unit.

If the window does not close tightly, maybe it wrongly exposed position of one or more loops. In this case, when opening the frame is to be mowed in one direction. This small problem you can remedy yourself. Adjust the loops of plastic windows is done using simple household tools that exist in every home. Record the step by step instructions that will help to quickly bring the window in order:

  • Open the window;
  • look for a loop at the upper opening of the hexagon;
  • Insert the hexagon of the appropriate size and start spinning in a clockwise direction;
  • in the same manner to adjust the lower hinge;
  • performing these actions, be careful to frame the situation equalized;
  • to get a perfectly flat vertical plane, use the building level.

These instructions may be adjustable plastic windows and doors brands Rehau (Rehau), Veka and KBE. Accessories from other manufacturers has a number of features, so-and-loop adjustment circuit will look completely different. However, to adjust itself to the plastic window is very simple. All these mechanisms work on the same principle. The main thing - to find and properly configure the appropriate hardware element in charge of the loop.

When it is hot outside, people ventilate housing. To do this, open all windows / doors in the kitchen and bathrooms. With intensive operation handle mechanism is loosened, so it needs adjustment. If your windows are always open smoothly and quietly begin to stick, try to solve the problem before it leads to more serious consequences. Adjust the plastic windows with their hands do not require the presence of special tools and possession of special technical skills. To handle re-worked the least, follow these steps:

  • open a window and refresh block mechanism grease pens;
  • check the position of the lock (it is on the part of the leaf, where the handle is located);
  • if it turns out that he worked late, press the lock into position, and then be able to freely turn the knob to the appropriate position (horizontally);
  • to check the serviceability of the internal mechanism, it is necessary to remove the handle itself with a screwdriver;
  • looking under the plastic cover, you may see an obvious problem and can correct it (for example, if one of the elements of the mechanism just took the wrong position);
  • use a screwdriver to try to solve the problem, but do not overdo it;
  • studying the internal mechanism of the handle, try to remove dirt (it is quite possible that the pen is jammed due to small foreign particles).

If these steps do not resolve the problem, it is necessary to call a specialist. Eliminate some faults without the assistance of an experienced master is almost impossible, so it is not necessary to experiment. Yourself understand the operation of complex plastic window mechanism is not so easy, because it offers many features.

The need to perform this procedure is defined very simply. If the seal loses its elasticity and its many cracks appear - it's time to replace it. Otherwise, the window will be free to allow air from the environment into the apartment, and even the most reliable mechanism will not save you from the cold, dust and noise. Replacing insulation on plastic windows carried out by the following algorithm:

  • open a window and starting at the top or bottom corner, carefully remove the old seal;
  • carefully treat the groove to remove all dust, dirt and grit;
  • in the same manner, starting from the top corner, insert the new seal across the width of the window;
  • Make sure that it is securely held in the groove along the entire length;
  • thereafter secure seal vertically controlling the position angles (do not stretch the rubber, or the angles do not match);
  • fasten the lower horizontal line, and then check the seal around the perimeter.

Of the preceding section, you learned how to handle domestic plastic windows independently for the winter season. If necessary, apply the appropriate instructions to ensure a snug fit the new seal to the frame. Turn eccentric to the maximum is not necessary, or new tires lose their elasticity for a few months, and you're going to have it replaced.

Video: Adjust the plastic windows with their hands

View video below, you will understand how to adjust the domestic plastic windows independently, without the involvement of specialists. Valuable tips will help you to adjust the hinges, customize winter mode and replace the rubber seal. Follow the simple instructions, and you can get the desired result and avoid common mistakes.

Adjust the plastic windows with their hands: the choice of instrument, the basic rules

Qualitatively new level of comfort in our home, considered plastic windows of polyvinyl chloride (PVC).

When installing these designs need professional help, but how to adjust the device independently of plastic in everyday use, is presented below in the recommendations.

Replacing traditional old wooden windows with modern, you need to periodically inspect the work of opening and closing mechanisms, status and functioning of accessories that will increase their durability and functionality.

Tool and hardware adjustment place of plastic windows

The most common faults, which can be managed without the help of a specialist:

  • When closing the transom frame touches the bottom or laterally.
  • Insufficiently tight fit to the frame transoms.
  • Striking plates worn out.
  • At the open flap in the "closed" does not open a window frame due to the lock knob.
  • Handle, crank, is loosely fitted to the frame or very tight turns.

You can troubleshoot using the tool:

  • pliers or plier;
  • hex key (size 4 mm);
  • flat and contoured (cross-head) screwdrivers;
  • a set of "key-asterisks" to adjust the pressing force;
  • scissors to cut seal;
  • oiler for lubrication fittings.

Main window setting rules of PVC with his own hands

Modern metal-plastic windows for optimum contact pressure of the seal around the perimeter of the leaf, the adjustment is carried out in three projections.

The individual elements, hardware configuration transoms and tools may vary, but taken as a basis the instructions below.

Summer and winter adjustment mode

A distinctive feature of the modern fittings of PVC windows is the ability to transfer it in the "winter" or "summer".

Window accessories is:

Because of the low price accessories such as the budget has limited functionality. It is produced mainly domestic producers and used in new buildings. In such metalaccessories missing translation function in different seasons, it allows the transom just open and close.

Window standard type fittings are widely used in the market, it is of high quality, produced with imported manufacturers. Transfer of winter or summer mode.

Species variants are used in a specialized hardware depending on the conditions. It happens: well fortified, burglar and for the input of plastic doors. This class is strengthening mainly equipped with a transfer function in different seasonal regimes.

To find out whether the hardware can be translated in different modes, pay attention to the presence of special pins (eccentrics), which are located side flaps, their shape (oval or not) and the presence of holes for hexagon screwdriver or an asterisk.

Sensing blowing on the edges of the frame to the onset of cold, generally at a temperature on the air to the level of the street plus 4-8 C, it is recommended to transfer the window frame in winter mode, and inversely during warming in the summer.

When winter mode window seals much wear, so no need to box better to leave in the summer. When the wear of the seal it is recommended to replace.

To put the fittings from one mode to another, it is better to turn to the master, but can be adjusted to a plastic window.

On the transom is necessary to find all the pins. The larger size of the glazing, the longer flap and more eccentrics, each of which is converted to the other mode. On the edge of the pin has a label indicating the desired mode. When the neutral position is tilted upward pointer.

  • In winter mode is transferred by adjusting the level of pressing the sash to the right, using the hex wrench, pliers or a screwdriver. Each pin is turned to the maximum so that the longest range at the close of the transom was sent to the room side and a notch on the controller out.
  • To put a window in the "summer" mode for micro-ventilation in the room turned toward all pin the shortest radius and the label on the controller.
  • Metalaccessories encountered when setting up which, at first you need to pull the cam itself (translation principle shooter pendulum of watches), and moving the hardware - turn back.

Check the result may be paying attention to how tight turns the handle when closing. When the winter mode, it will turn tighter due to the tight pressing the shutter.

Check the transom down force may be holding it a regular piece of paper. When you try to pull the sheet under the regime of "winter" it will be difficult to stretch and even tear and at summer - stretches easily.

The reasons that lead to the weakening of the loop:

  • sash frame clatter shrinkage walls and loops have an additional load;
  • the displacement of the frame level during installation;
  • sloppy closing and opening of the frame;
  • sagging shutters due to the load on the loop;
  • box is installed and has been used for a long time, so lost tightness due to the wear of the seal rubber.

How to adjust independently the upper hinge

To resolve this problem, connected with opening transom wrong or bad it fit, fold in the area of ​​the upper hinge and pressed open.

Blowing on the hinge side is found in violation of the window frame assembly. To control this problem, with the sash and the glazing bead is removed in the middle between the profile and the glass enclose several straightening plates. To this end, a wide chisel leans in the joint between the transom profile and bead and gently blow disconnected bead.

At home aligning plate is made of an ordinary wooden ruler. Their use should try not to damage the glazing.

Adjustment in the vertical and horizontal direction loop

If the middle or the lower part of the transom touches the window frame of the sash slack, then it can be eliminated by adjusting the rise of the horizontal or vertical slide.

  • Horizontally adjusted via the top or bottom loops. When you open a window frame by inserting Allen key into the hole and turning it to the right side, the flap will be attracted to the loop, and this loop opposite bottom corner, climb. When rotated in the opposite direction it moves away from the hinge transom and the opposite top corner of the loop is omitted.
  • Bottom hinge can be adjusted to open at the inner side of the window frame and the outside - with closed. Adjustment is similar to the upper loop. These methods can slide frame or to achieve elimination of the bevel.
  • By vertical adjustment of the bottom loop is performed by rotating the key in the hexagonal hole of the adjusting concealed under the cap bottom hinge.

When rotating the frame lying right and left by rotation - is omitted.

If the seal is bad surrounding rubber may occur drafts. For a more snug fit transoms to the frame, the key on the hinge side, regulate the clamping mechanism. When a stronger vydviganii tab located on the sash, glazing will be strongly pressed to the frame and vice versa. The loop with the right arrangement to push the tab, rotate the hexagon to the right side, and left-hinged key is rotated to the left.

pressing the upper loop adjustment is performed or both at once. It depends on the type of accessories. Forging clamp the lower loop, you need to remove the cap and rotate the screw, located perpendicular to the plane of the window frame.

Adjustment of the upper hinge clamp is only carried out on the transom that recline. In order to get a hexagon, in charge of the force pressing the upper sash, window open, then turn the knob to the ventilation mode. In this position, you must provide additional fixation of glass, since all the weight falls on the loop at the bottom.

Repair and adjustment of the window handle

When replacing a broken handle plastic windows, you in the direction of the pull pad handles and deploy it at a right angle, loosen the screws. Old pen is removed, install a new patch is returned to the position.

With a lack of lubrication can handle tight turn. To resolve this problem fitting mechanisms need to be processed by machine oil or aerosol lubricants.

Technical inspection and lubrication of window hardware is preferably carried out annually, and in the presence of visible defects - often.

When caring for windows made of plastic, and adjust them, be aware that:

  • from time to time you need to check the condition of the seals, so as not to miss their deterioration;
  • decorative cover made of plastic should be removed very carefully, trying not to bend or crush it during work prophylactically;
  • when the curvature of the frame or window opening adjustment windows are best carried out by contacting a specialist.

Regularly inspecting the state metalaccessories timely eliminating problems arising during the operation of plastic windows, they will be a long time to operate, keeping the house cozy and warm.

Tools and material, get rid of mosquitoes

In the kitchen bred bugs: insects, causes of, and prevention methods to combat

How to clean a toilet: features and advice for getting a good result

How to whiten your own Underwear: effective tools and methods for washing

book of dream interpretations

© 2009-2017 Female online magazine «Ladyplace»

All rights for materials and information in the women 'Ledipleys "online magazine are protected by copyright and related rights. Copying and use of materials is allowed only in the case of active link to the source.

The methods and schemes adjustment plastic window

Plastic windows have long proven to be a reliable and robust frames, preserving room temperature mode, preventing penetrate drafts. Many users install plastic, but often do not conduct proper maintenance and forget about the details of the use of a transition to seasonal conditions and other relevant details. Correct adjustment of plastic doors and timely care - is the foundation of a long service life of the window frame, eliminating frequent repairs.

Often the adjustment fitting of plastic windows is required at the low quality of the installation work when the design was not aligned vertically and horizontally. Adjustment is required in the case of natural wear and tear, as over time the window hurt fitting elements. In the case of a weakly sealed flaps windows let the cold air from the window starts to blow.

Useful information on how to adjust the plastic windows independently, it is useful to each owner of a window of plastic. Thus, the need for simple tools that are in each house:

  • Allen key;
  • screwdriver.

Before setting up a mechanism is necessary to examine the window fittings

Look at the window to determine the installed hardware as adjustment plastic window will depend on this factor. In one case, the flap need to be removed, the other will be sufficient tightening of the fixing screw.

Set up the horizontal and vertical axis

The horizontal flap side subject to adjustment in case bevel frame provoked shrinkage design, improper opening of the window or loose fitting elements. In order to resolve this issue in the Window Hinges insert hex wrench, turning clockwise until the moment when the flap is not sufficient to keep away from the distance of the loop.

Setting the window mechanism is carried by a hexagonal key

The lower part of the opposite standing element should drop significantly. Adjusting the upper loop of a plastic window at this shall be deemed terminated.

Adjustment of the lower loop is performed from the outside. Shifts are usually averages of 2 mm.

Scheme adjust the upper and lower loops

Vertically, you can adjust the window with hinged loop located at the bottom of the frame. With the cap removed hinge and begin tuning rotational motion mechanism. in the direction of movement of the tool clockwise will allow to lift the flap movement in the opposite direction - to lower.

Adjust the window mechanism is necessary to smooth rotation

Regulation of plastic structures should be smooth manner so that the mechanisms have not shifted by more than 2 mm in one approach. For tight press the sash characteristic direction of the risks facing the seal. If the risk of looking exactly the opposite, you need to pull the flap.

Adjust the plastic windows with their hands does not cause a lot of difficulties in the timely approach, allowing the device to adjust the window mechanisms at the highest level.

Fold longer be closed: a solution

Adjusting the clamping of plastic windows will be essential when the window from the open position is not transferred to the closed mode. Often the cause of the castle stands a device which does not allow to turn the knob. Action Technique is fitting brand. Some instances provided with a thin plate spring fitted on the inside, which is necessary to press and turn the knob to close the window. Other items are provided with tongue under the handle - the pressure-sensitive blocking it adjusted mechanism is removed.

If you stopped to close the flap, you need to unlock the lock

In a situation where the window still does not want to close, need a small repair of plastic windows. You must open the fold, look for a mechanism element, which serves as a hook tongue loosen and install on the inside of his hand a thin plate. The decision will contribute to a shift mechanism closer to the second leg member. As a result, increase the contact area, allowing the window to close without any difficulty.

Adjust the plastic windows on the level of a clip

Clamp plastic window to configure simply, if you follow the sequence of actions. Find the area of ​​the handle located at the side end, a system of cams, which are the main instrument of adjustment.

Winter and summer mode is configured using the pins

Their external performance may be somewhat different depending on the manufacturer of the window, but the principle of action is the same, whatever their species. Using an Allen wrench or pliers desired degree of pressing is adjusted by rotating the eccentrics flaps. During the summer, experts recommend installing weak regimes, moving to stronger closer to the winter.

In the summer of put up a weak mode pressing the window, and in the winter - strong

When you need to make adjustments by pressing the window hinges, it is necessary to turn the adjusting screw on the bottom of the loop. By the swing-flap apply further adjustments, using the upper loop. In order to successfully reach the adjustment screw located on the scissors next to the top of the loop, you need to open the window, put pressure on the lock tab and set the knob on the ventilation mode. When you need to press the shutter to the window frame, the bolt is rotated in a clockwise direction. Rotation in the opposite direction will contribute to weakening.

By adjusting the swing-out scissors, you can adjust the degree of the pressing box

Adjustment of window fittings with plastic windows depends on the manufacturer, as there are varieties of adjustable only screwdrivers, located on the side of the pens. They can be adjusted with an Allen key. To increase the clamping strap gently shifted to the side street. If you look at the loops, you will notice put forward by the pressing members. Less promotion will provide a weak adhesion, and more tightly squeeze the sash to the frame.

How to clean accumulated dust from the fittings

Repair and adjustment of plastic windows is also associated with high-quality care for the windows, which are in need of deep cleaning of accumulated dirt in hard to reach places. Not promptly cleaned windows, sooner or later you will have to repair them as a functional of the garbage will be broken. Repair of plastic windows quite time-consuming in terms of weight of the structure, so it is desirable to work with assistants.

Scheme adjusting elements for driving them in purity and procedure:

  • remove leaf from its hinges by removing the overhead frame elements;
  • remove the upper left and right;
  • remove the flap from the lower hinge;
  • carefully set aside.

Removing sash with loops should be carried out with an assistant

Next, the leaf area thoroughly inspected and spun fixed screws on it. Details of the mechanism is well washed, preferably using specialized solutions that are easy to apply with a brush. Upon completion of the procedure design is well dried in the open air or by means of cold air from the dryer. Each moving mechanism applied lubricant, whereupon fittings going in reverse order and is set to the original location. After adjustment of plastic windows do not forget to lubricate the window on each loop.

Before assembling the window all the elements necessary to grease fittings

Adjust the plastic window is not technically difficult, because detailed instructions contain only a few steps that are recommended to be performed in strict sequence.

Questions on adjusting window frames often associated with the work of pens, because they can occasionally break or lose functionality. It is important to remember that the handle of the plastic windows require periodic attention, because more often than other parts exposed to rapid wear: sometimes they need a repair or complete replacement.

Adjust the plastic windows independently would be a quick fix to lose their functionality handles. So, pretty crank handle requires tightening fasteners, which can hold in a matter of minutes, as the name refers to the failure of the easiest types of repairs.

Under the escutcheon are the bolts that tighten up the screwdriver

So, get a handle trim piece formed in the shape of a rectangle, gently hook the fingers on both edges and turn through 90 °. Under the plate there is a pair of bolts that need to tighten cross-shaped screwdriver. To raise the plate covering the screws, do not use tools, because there is a likelihood of damage to the profile of the surface and disturb the shape of the plug element.

Adjust the plastic window itself can be the case when the fuses on the window handles, which are applied with the aim to protect children from the self-opening windows, fail. In case of breakdown of the device to hook fingers plug gently followed loosening the holding bolt. Light rocking motion removed the handle. If necessary, replaced by a new instance and set in the same way back.

To replace the fuses by opening the windows will need to remove the handle

Another common problem is to close the plastic window sash little functional handle that occasionally jammed and does not reach the required limits. In this case it is necessary to lubricate mounting machine oil using a cotton swab. Also suitable special spray or silicone grease.

The problem of seizing the handle can be solved by oiling fixtures

To fix or replace the handle is rotated 90 °, after which the plate is removed in the form of holders screws. Otkruchennuyu handle easily replaced by tightening the screws in the same sequence. Repair of plastic windows with complete hardware replacement is inevitable, if the handle thoroughly stuck. Cases are extremely rare, but it does happen.

Adjust the plastic windows with their hands not be easy for the owners, because the manipulations are simple enough. It is only important to approach setting up a share of responsibility and to follow instructions demonstrating how to conduct adjustments or perform structural repairs.

Leave a Reply

Your email address will not be published. Required fields are marked *

11 − = 4