How to make an arch with their hands Plasterboard

A significant drawback of this design is to reduce the size of the door opening. To see whether the well arch fit into a particular doorway, it is better initially to cut the blank paper or cardboard and attach it above the door. If the opening height less than 2.5 m, it may be necessary to reduce the arc bending or make small bends only at the corners of the arch.

Mounting of arch with a small bending radius

Compasses make possible and trimming of the metal profile

1. The first step is to cut through the first layer and the cardboard core of the gypsum. To this end, the planned line applied line and along it are held several times sharp knife or sawing metal.

Cutting the first two layers

Cut the second layer

Cutting the blanks for the upper vault arches

Most convenient to work with jigsaw or a plane for special plasterboard. With them, you can cut any shape of plasterboard. Moreover, with this method is practically not dusty gypsum, and the resulting edge almost do not require additional processing.

Cutting knife-saw for drywall

The crown for drill

Cutting and bending metal rails

Aluminum rails are cut conventional Shears for metal. For fastening the top of the arch will need a special arched profile. It can be purchased at the store or make your own hands.

For devices arches can be purchased arch drywall. It is more ductile and, since its thickness is smaller than conventional sheet easily bends. However, buying a list quite expensive. Some stores sell such material is not sheets and segments, which is very convenient. If the purchase is not possible to cut small, can be bent, and an ordinary sheet of drywall.

Slim Arch drywall easily bent, but is more expensive

Before the flexible workpiece is rolled spiked roller

Dry flexible drywall

After dismantling of the door frame from the exfoliated surface purified plaster dust and dirt and knock all irregularities. Further, on each side of the doorway using dowels, screws with 20-30 cm increments are fixed Two rack-mount metal profile. Thus, a departure from the edge of 11-12 mm for drywall and applying putty. If the opening width is large (more than 1 m), are attached between the guides jumper. Small segments profiles, connecting the two side rails are mounted in the bottom of the opening. They should rest on the floor.

Fastening of the upper profile

Mounting profile with jumpers

Between the segments of the profile are fastened with screws

The earliest screws in increments of 25-35 cm are attached to the preform upper semicircle arch. Their width should be equal to the width of the door opening plus 10-15 mm. It should not be fastened screws too close to the corners - it is necessary to indent 1-1.5 cm, or at fixing cracks appear.

After installation arch covered with putty

How to make an arch made of plasterboard with their hands: step by step guide

Interior arch of the drywall is currently one of the most popular types of door designs. This design of the opening can be done easily by hand. To do this, you need to know the basic principles of carrying out this work, and to understand the materials used. The rest - it is imagination and skills of the master himself.

Drywall - the most popular material for the manufacture of arch structures

The advantages of plasterboard arches

Production of arches made of plasterboard is not just enjoyed so immensely popular. Their prevalence in the interiors of modern apartments and houses due to a number of advantages in comparison not only with the standard door designs, but also with other materials used for such purposes:

  • Appearance. Drywall allows you to create any shape and combine a variety of shapes in a single product. In addition, it looks quite neat and easy to further finishing.
  • Simple manufacture. So how to do it the easiest way to arch made of plasterboard, many masters prefer it to this material. It is simple in processing and cutting, is mounted on the frame without difficulty. In addition, it can be bend on the template you want.
  • A variety of finishing options. Of finishes to give a decorative kind there is an unlimited amount. This is possible thanks to a flat surface.
  • Ease. Plasterboard sheets do not have an excessive load on the supporting structures of the building.
  • Durability. Such constructions sufficiently solid and resistant to destructive factors.

The main advantage of gypsum arches - is the ability to create custom shapes passage

Arch made of plasterboard with their hands - it is quite feasible task. For beginners, you can do a simple option and professionals can create sophisticated compositions inside walls.

Especially popular are the arch of the drywall in the hallway, kitchen, living room or on the balcony.

Tools and materials needed

Before you make an arch made of plasterboard with their hands, you need to prepare all the necessary tools and acquire suitable materials. You will need to create such a structure:

  • hacksaw or jigsaw;
  • measuring tape and a pencil;
  • level;
  • Metal scissors;
  • screws;
  • plugs;
  • screwdriver;
  • stationery knife;
  • sandpaper;
  • metal profiles;
  • drywall sheets.

The main tools for making the arch made of plasterboard with their hands

Also, for the manufacture of the arches of the GCR you need a metal substrate, ie the frame device. Used for this purpose several options of special aluminum profile:

  • guide;
  • rack;
  • arched;
  • reinforced corners;
  • connectors for each type.

Arch can be done independently of the conventional U-shaped profile, make an incision in increments of about 5 cm in length. Plasterboard is better to choose a 12 mm thick waterproof and ceiling for the arch of the arch - 6.5 mm.

Species profile for drywall

So to make arch of the drywall in the doorway, you first need to perform layout details. To do this baster contours arches on the wall according to pre-thought-out plan. Measure the height of the opening, determine its center point.

It is best to adjust the data in the installation process. According to the size of the trimmed metal part construction, i.e. the frame and then determines the size of the gypsum boards for plating.

To create the arch of the drywall first need to perform layout parts

Aluminum is cut very simply - using scissors for metal. Cutting is performed by using drywall jigsaw on marked lines. This applies mainly shaped parts. Straight cut can be done with a knife stationery. We need to make a smooth cut, poring through the cardboard in gypsum layer. Then put the material on the table and push down to break off on the contour element.

In some cases, you may need to increase the space in the opening. In this case, you need to address this issue in advance and to cut off part of the wall. For load-bearing structures, for example, in the hallway, there are limitations. Secondary partitions can be completely demolished and build it in parallel with the construction of arches.

With a simple pencil on plasterboard sheet marked contour arches, and then a small cut with a hacksaw or jigsaw

Shape the future design created exclusively by using the profile. The frame carries a skeleton role in the design and retains all of its elements. Consider how the form of the arch profile.

Before you make an arch made of plasterboard, you must first install the guiding elements in the doorway. For this purpose the corresponding U-shaped profile. He bolted to the floor and ceiling, according to a pre-designed pattern of the project.

Next is the manufacturing bases for vertical frame for future arch. The guides are driven rack and screwed screws. It is mounted directly on top of the metal arch itself. Its shape can be displayed with their own hands, arching profile accordingly.

To create a frame used arched profile or is cut and bent U-shaped line

After the frame profile can be ready to proceed to the skin structure. For this it is necessary to cut the material to form respective segments. The front of the arch of the drywall is derived from the wall sheets. It is important to take account of their thickness, so no further formed projections or depressions in the total wall structure.

Plasterboard is fastened on the frame by means of screws with a pitch of 10-15 cm. The inner cladding is used drywall ceiling. It is thinner, and therefore it is easier to fix and give it the desired shape.

Since the interior of the arch have bending plasterboard on the vault, the material was incised with one hand and moistened with water so that it can be bent.

The basic steps of creating the simple arch of plasterboard

Next, you are ready to finish. To this end, the corners are strengthened corner profiles, and applied serpyanka joints. With the help of putty you need to cover up all the cracks and place screwing screws. After that, the surface is primed and fully shpaklyuyut.

After drying and smoothing of the surface can take the opening clearance. In the hall it can be decorative stone or stucco, and in the living room - paint, wallpaper or MDF panels. Simple designs can complement duct suitable form. But for complex options will be sufficient to finish plaster and paint. Additionally, you can equip the arch lights. All wires easily hidden inside the structure during the creation of frame and cladding.

In this installation of the arch is completed. What will be the final finish depends on interior style and personal preferences.

available easily and beautifully

Copying site materials is allowed only if active link to the source.

Arch with their own hands: step by step instructions (drywall), 3 ways

One way to increase the living space - to remove the door. But it does not always have the opportunity or the desire to destroy the wall. Then the former doorway shaped in the form of an arch. Another usage of arched openings - split a long corridor into zones, breaking too simple geometry. When repairs on their own often do arch made of plasterboard: with their hands to make them easier.

Interior doors or corridor arch may have different shapes. They differ mainly in the form of the top and sometimes - means connected to the vertical portions. Their main species are represented in the photo.

Types of arches and interior corridor

This group is not one of the most popular in recent years - poluarka. They have rounded a corner on one side only, with the other he is straight. Hence the name - poluarka. She looks good in modern intrerah: minimalism, hi-tech, can be - in an art-deco style.

One of the options in the interior poluarki

Classical differs correct form the top. This is strictly a semicircle whose radius is equal to half the width of the door opening. This view looks good when the opening height of at least 2.5 m. Good fit in any room, but it is best looked at in a long corridor, or in lieu of the front door in the kitchen.

required height of at least 2.5 m for the classical arch

Arched doorway in "Modern" style differs a small radius of curvature and the sharp transition at the junction with the vertical gap is. It looks good, if the walls and ceiling are more or less simple design. Looks great on the former site of the balcony door, is good when entering the room.

Arch in the Art Nouveau style on the former site of the balcony door

Arch style "Romance" is a rather simple rounded corners (mainly craftsmen and so it is called). It looks good with a large width and the greatest height.

Shape "romance" is good for a large width and a small height

Shape "ellipse", "very close to the" romance. " It differs only in the greater curvature of the middle part. Also suitable for low and wide openings. It looks just a little softer.

Suitable for a large opening width and is not very great height

Trapeze - non-standard design, consisting of polylines. Heavily played up in the interior, because is not often used: for some non-standard designs.

One of the design options - Keystone

Very similar to a normal opening, but it is in fact it is, but without the door leaf. For greater originality is often accompanied by carved wooden elements in the form of columns on each side. As such, good for classic interiors, as well as ethno-style - Greek or Roman, depending on the type of column.

Portal with a frame made of wood

For decoration in contemporary style using a different note - next to the main arch, a smaller portals. This technique allows us to "beat" a simple form.

Another version of the "portal" arch

Before proceeding to the manufacture of the arch, you need to define its parameters. select the type and then Options: where it will start and what is the radius of curvature. It can be really sharp bend, and can only be a rounding of corners.

Rounded corners in standard doorways look better than the steep arched curves

To understand how the form you prefer to watch, you can cut a template out of cardboard and tape it to the door. To assess the effect. If all you are satisfied, it is possible for this pattern to make the preform. But only one - for one of the sides of the opening. The second should be done at the place, not to get crooked.

Step by step instructions with photos: the fastest way

Arch made of plasterboard with their hands doing a variety of ways. This takes a minimum amount of time. Having defined the form of attempting to install. On opening prepared - cleaned of flaking plaster and relatively balanced, the size of the future arch fasten frame. It is made from a profile for plasterboard or dry piece of wood of suitable size. Sometimes, if the wall is narrow, you can only choose wood.

According to the selected size bolted frame profile

To begin, cut out a rectangle the size of drywall arches future, find his middle note and then temporarily fasten into place. Back down from the edge of 12.5 mm - thick sheet of drywall. If the adjacent walls plastered already, add a couple of millimeters in the plaster - to be able to align the surface.

Screw the drywall in place

Now, take a piece of profile or hard corners, from one edge postpone half width of an aperture. At this point in the corner to make the holes, insert cloves into it. This marked a nail stuck in the earlier middle of the doorway on the sheet. It turns out a kind of compass with which to easily draw a perfect line.

Means for delineating an arc

By changing the mounting height can be obtained more or less high arch. If you need a flatter curve, increase the length of the "circle".

By means of tracing the corner arc

After removing the sheet with the planned contour arc cut. It is possible to make a special sawing plasterboard, metal saw - fine tooth for a smoother edge, jigsaw (will be a lot of dust). If the cut was not very smooth, it align with the help of fixed grated sandpaper. This device achieve a perfectly flat form we need a curve. Carved arches piece - side wall - again fasten into place.

The cut fragment anchoring

If all is equal, no bias or irregularities not, on the other side of the opening attach a sheet of drywall is a few steps before - a rectangle or square - depending on the form. It must be fixed vertically. Now transfer the shape of the arch to it. Take the square, right angles and one side is pressed against the drywall, which transfer the arch, the second party - to the body. Putting perpendicular angle, note the pencil point. These points do across the arc. The more often they will be made, the easier it will be to draw a line and more accurately match - less have to grind.

We transfer arch shape to another sheet of drywall

Why is it so difficult, and not just make a copy of the first sheet? Because there is little openings which are symmetrical. As a result, set the second sheet so that the lines coincide arch very problematic.

Noting all the points, we remove the sheet, draw a line, Scrollsaw on it. Mount in its place. Now again take a trowel with sandpaper and now leveled both edges to complete coincidence. One point - the ironing board should be wider opening to a single pass captured both arches wall.

Equaled both walls simultaneously

We measure the arc length, cut a piece of the profile of the same length, making incisions on the walls every 3-4 cm. This tape will need to fasten the arch along the arch of the one and the other.

How to cut a profile for arches

Is attached to the screws, gently pressing and holding the profile of its bar, not his fingers to get the screws on the fingers elementary. By the way, with the cut profile is necessary to work with gloves. If no - hands slice the exact.

Fasten notched profile, simultaneously giving it the shape of an arch

By the way, back in the profile can be set on the edge - it's easier to work, and the joint then still have to close up. Similarly, the strip is screwed to the other side.

This view from below - on the sides attached Profile

There is a second way of mounting profile - to put him to quickly grasp the universal glue, such as liquid nails. This method is acceptable, if a small opening width. With large thickness of the arch, the adhesive can not withstand the weight of gypsum board that will be secured from below.

The next step - fasten jumper. First be lost depth arch subtracted from 1-1.5 cm. This will be the length of the jumper. Cut pieces of the profile of this length.

The jumpers are cut from the same profile

In places jumpers mounting cut off "petals", is established and secured prepared fragment. It must not rest against the wall, is located at a distance of 5 mm from the back. Jumpers need to design turned tighter or she "walks" when pressed.

Further plasterboard be cut rectangle that will cover the design below. Its width is determined by a - from the outer edge of a single sheet of plasterboard to the outer edge of the second sheet. Measured length flexible strap (sartorius) with a tape or assistant. This sheet is fastened with screws to the frame arch. Sheet accounts bend, and how to do this, see below - towards the end of the article.

We attach the strip to the arch giposkartona

Next were finishing work: on an angle fastened special corner all puttied on the conventional technology, first start the joints and corners, then finish.

The arched opening plasterboard: second method (photos)

This method is good if the thickness of the walls is small: try to attach the profiles if the gap between a few centimeters, and even then to fix the bridge. It begins as: cut first arch wall, secured and transferred to the second sheet.

At first, too, cut the sidewall

After the width of the gap between two sheets of cut wooden perekladinki, which are mounted along the edge of the arch on the screws.

Insert the cut width of the opening wooden blocks

Cut a strip of drywall is attached, since one of the parties. To make it more convenient, you can lock the clamps, the benefit of a small thickness of the partition. When mounting strip can be guided on the screws which fasten the bars. So what exactly will get the shot off.

By means of the strip can be fixed clamps

Then it remains only to fix a special corner of the perforated area and raze irregularities.

By arch arch attached Area, all puttied

Caulking can hide all the flaws

Dub dried plaster of the arch is also convenient to the entire plane of sandpaper attached to a grater. Unfortunate that while the dust pours into the eyes, so it is almost impossible to work without glasses.

Arch made of plasterboard with their hands ready

How to make the arch instead of a door: a third method - type-setting machines

Another way to make an arch made of plasterboard with their hands - typesetting. Body divided into segments and assembled from pieces that create close to the desired curvature.

Arch collected from the plates, cut plasterboard

Attach them to the filler, diluted with a mixture of PVA and water. Dries a batch quickly, because first cut into the plate and try on. You can lay down on a table, only a set of turn upside down, but how true is collected to evaluate the plate will allow.

View of the doorway arch side

The plates were then begin to attach to the opening for enhancing reliability periodically screws. Under the head enclose washers - not to push the cardboard. Remove excess putty immediately. If the grab, tear unreal. The finished surface are primed to improve adhesion (adhesion), and then shpaklyuyut aligning arch. To make it easier to display, you can use the template attached on both sides.

Zashpaklevanaya arch looks

Making this technology tight bends is not easy, and for the rounded corners and poluarok - a great way to do without profiles.

One important detail: standard plasterboard wall bends badly. For curved surfaces specially invented thin - 6 and 6 mm thickness. That a bent portion is easier to make out of it. With such a small curvature of the thin sheet may bend easily and contrivances. If a thin GVL has no desire to buy, there are two ways to bend the standard.

First - take the needle roller and well-cut segment is rolled from one side. I need to roll with the effort to break up the cast. Then a sheet wet with water and leave it for two or three hours. After these procedures, it must be nice to bend. Take fix it with one hand, and gradually pressed to the frame arches, bending, screwing screws gradually at the edges. The method is quite good, only the lack of experience and lack of treatment of gypsum sheet may burst. And then have to mask the slot, or start all over again.

Roller with needles rolled strip

Second way to bend drywall:. on the one hand to make incisions with a knife about every 4-5 cm incisions should cut the paper. This band is also gradually fastened, breaking the plaster as necessary. He cut lines bursting with light pressure.

Notches on the one hand make it easy to break the plaster

Leave a Reply

Your email address will not be published. Required fields are marked *

− 1 = 4